S120 Submersible Cylinder Sensor

The 350bar S120 is a submersible version of the P100 in-cylinder linear sensor with a larger electronics housing and wet mate high pressure connector. The S120 is sealed for a maximum of 350bar combined hydraulic and water pressure. The unit is compact, space-efficient and responsive along almost its entire length.

Like all Positek® sensors, the S120 provides a linear output proportional to displacement. Each sensor is supplied with the output calibrated to the travel required by the customer, our standard range covers any measurement range from 0-5mm to 0-800mm. As with all of our packaged sensors full EMC protection is built in.

The sensor is very robust, the body and target tube are made of 316 stainless steel for long service life and environmental resistance.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install with M18 or 3/4″ UNF mounting thread options. The target tube can be supplied plain or with a variety of flanges. The S120 also offers a wide range of electrical options.

This sensor is waterproof for submersion to 3500 meters (350bar) combined water and hydraulic pressure.

View all Linear Sensors

 

Description

The Positek S120 cylinder sensor is a submersible version of the P100 in-cylinder linear sensor with a larger electronics housing and wet mate high pressure connector. The S120 is sealed for a maximum of 350bar combined hydraulic and water pressure. The unit is compact, space-efficient and responsive along almost its entire length.

Like all Positek® sensors, the S120 submersible cylinder sensor provides a linear output proportional to displacement. Each sensor is supplied with the output calibrated to the travel required by the customer, our standard range covers any measurement range from 0-5mm to 0-800mm. If your application requires 10″ (254mm) measurement, then Positek will manufacture the sensor specifically for this angular range. The sensor will measure 10º; however, will still rotate through 254mm. As with all of our packaged sensors full EMC protection is built in.

The sensor is very robust, the body and target tube are made of 316 stainless steel for long service life and environmental resistance.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The Positek sensor is easy to install with M18 or 3/4″ UNF mounting thread options. The target tube can be supplied plain or with a variety of flanges. The S120 also offers a wide range of electrical options.

This sensor is waterproof for submersion up to 3500 meters (350bar) combined water and hydraulic pressure.

Follow us on Facebook

Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:

 

Measurement Range

Factory set to any length from 0-5mm to 0-800mm in increments of 1mm. For example, if your application requires 10" (254mm) measurement, then Positek will manufacture the sensor specifically for this angular range. The sensor will measure 10° however will still rotate through 254mm.

 

Electronic Options

Output Signal Supply Input Option Code
Standard    
0.5V to 4.5V DC ratiometric +5V DC nom. ±0.5V A
Buffered    
0.5V-4.5V DC +24V DC nom. +9-28V G
±0.5V DC ±15V DC nom. ±9-28V B
0.5-9.5V DC +24V DC nom. +13-28V C
±10V DC ±15V DC nom. ±13.5-28V D
4-20mA (2 wire) +24V DC nom. +18-28V E
4-20mA (3 wire sink) +24V DC nom. +13-28V F
4-20mA (3 wire source) +24V DC nom. +13-28V H

 

Connector/Cable Options

Option Option Code
Axial micro wet mate bulkhead and mating connector with 50cm flying lead (standard fit)
Mating connector with longer cables available as special.
J50
Radial micro wet mate bulkhead and mating connector with 50cm flying lead (standard fit)
Mating connector with longer cables available as special.
K50
Cable length - The standard length of cable supplied with a Positek position sensor is 50cm although you can specify any length you require. Specified in cm after the L or I e.g. L200 for 200cm cable from axial cable gland

 

Mounting Thread Options

Option Option Code
M18 Thread T
3/4" UNF P

 

Target Tube Flange Options

Option Option Code
None U
Penny and Giles HLP100 V
Temposonics (M4 fixing) W
Parker Hannifin Cylinder Version X

 

<+/-0.1% FSO Linearity error (10mm minimum stroke length) Option Code
Z650

Dimensions

Body Diameter 40mm
Target Tube Outside Diameter 9.45mm
Travel Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
Independent Linearity <±0.25% up to 450mm
<±0.50% over 450mm at 20°C
<±0.1% available on request
Temperature Coefficient <±0.01%/°C Gain & <±0.01%FS/°C Offset
Resolution Infinite
Noise

<0.02% FSO

Frequency Response

>10KHz (-3dB);
>300Hz (-3dB); 2 wire 4-20mA

 

Output Signal and Output Load

Output Signal Output Load
0.5 to 4.5 V DC ratiometric 5k Ohms min
0.5 to 4.5 V DC 5k Ohms min
± 5V DC 5k Ohms min
± 10V DC 5k Ohms min
0.5 to 9.5 V DC< 5k Ohms min
4 to 20mA (2 wire) 300 Ohms max at 24V
4 to 20mA (3 wire sink) 950 Ohms max at 24V
4 to 20mA (3 wire source) 300 Ohms max at 24V
Supply Current 12 mA Typical 20 mA max (voltage versions)

 

Temperature Limits

Operating -4 to +50°C
Storage -4 to +50°C

 

Other

EMC Susceptibility EN 61000-6-2
EMC Radiated EN 61000-6-3
Vibration IEC 68-2-6: 10g
Shock/td>

IEC 68-2-29: 40g
Sealing IP68 350bar, 5000psi, 3500m (combined hydraulic and water pressure)
Electrical Connections Micro wet mate connector